Fuse link
Do not damage fuse holders, do not generate fires, do not burn electrical contacts
40 YEARS MANUFACTURING
el fusible de alta calidad
Nosotros prensamos
adicionalmente soldamos
Tubos en fibra vulcanizada
¿Are you properly protecting your transformer against overcurrent?
Por qué nuestros fusibles duales?
Nuestro fusible de expulsión de doble acción ofrece la mejor protección a la red eléctrica y transformadores. Fabricamos nuestros productos bajo los más altos estándares de calidad.
- Cumplimos con normativas técnicas
- IEEE STD C37.41:2016
- IEEE STD C37.42:2016
- NTC 2132:2006
- NTC 2133:2002
Caracteristicas generales de nuestros fusibles de expulsion
FRECUENCY
Se pueden aplicar en sistemas de 50 a 60 Hz.
OPERATIONAL TEMPERATURE
Están clasificados para ser utilizados a una temperatura máxima de aplicación de 40 °C y no inferior a -30 °C.
THERE ARE NO LIMITATIONS OF USE DUE TO ENVIRONMENTAL CONDITIONS .
0.5, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 15, 20, 25, 30, 40, 50, 60, 65, 75, 80, 100, 125, 140, 150, 200 A.
Tipo T (ELEMENTO LENTO) con relación de velocidad de 10.0 – 8.1:
0.5, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 15, 20, 25, 30, 40, 50, 60, 65, 75, 80, 100, 125, 140, 150, 200 A.
Tipo H (ELEMENTO EXTRA RAPIDO) con relación de velocidad de 4.7 – 7.1 :
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 15, 20, 25, 30, 40, 50, 60, 65, 75, 80, 100 A.
Tipo dual SR (ELEMENTO LENTO – RAPIDO) con relación de velocidad de 13.1 – 21.5 :
0.2, 0.3, 0.4, 0.6, 0.7, 1.0, 1.3, 1.4, 1.6, 2.1, 3.1, 3.5, 4.2, 5.2, 6.3, 7.0, 7.8, 10.4, 14.0, 21.0, 32.0, 46.0 A.
Tipo VS (ELEMENTO MUY LENTO) con relación de velocidad de 18.0 – 24.3:
0.5, 1, 1.5, 2, 3, 4, 5, 6, 7, 8, 10, 12, 15, 20, 25, 30, 40, 50, 65, 80, 100 A.
Tipo M (VELOCIDAD STANDARD) con relación de velocidad de 7.0 – 9:
1, 1.5, 2, 3, 5, 6, 7, 8, 10, 15, 20, 25, 30, 40, 50, 65, 80, 100 A.
LUHFSER distribution dropout fuse cutout for expulsion fuses.
- Nominal current
50, 100 and 200 A distribution dropout fuse cutout
- Nominal voltage in kV.
The rated voltage of the dropout fuse cutout is defined as a function of the phase-to-neutral voltage and the phase-to-phase voltage.
- Interruption capability
It is the maximum fault current that the dropout fuse cutout can interrupt without damage.
LUHFSER expulsion fuses manufactured by ELECTRICOS INTERNACIONAL SAS, are installed in distribution dropout fuse cutout for overhead networks and protect distribution transformers, overhead lines, branch lines, reclosers and other devices, in circuits with voltages in the range of 6 to 38 Kv, against overload and short-current faults.
USES Selection, application and coordination of Luhfser brand fuse wires.
- fuses to protect the transformer:
Protección de la sobrecarga Protección de cortocircuito Capacidad para soportar las corrientes de entrada o irrupción y sobretensiones.
- Coordination of fuses with each other
- Selection of fuses on feeder lines
- Fuse selection for recloser coordination.
- Capacitor bank protection reliability conditions for proper operation
Does not melt when it should not
La seguridad es el aspecto de la confiabilidad que expresa el grado de certeza de que el fusible no operara incorrectamente bajo condiciones normales. Se mide como la probabilidad de que el sistema de protecciones no presente actuaciones de falla o que actúen otras protecciones diferentes a las que debieron actua
Does not melt when it should not
Reliability is the aspect of reliability that expresses the degree of certainty that the protection system will operate correctly in the presence of an abnormal condition or fault, taking the necessary actions in this situation. It is measured as the probability that the system will act effectively in the presence of a fault.
LUHFSER expulsion fuses should be installed according to the following recommendations:
- Removal of the washer is prohibited
- Removal of the tube is prohibited
- Weakening the cable is prohibited
- Weakening the wire is prohibited
- It is prohibited to cut the cable at the lower contact of the fuse holder.
In a three-phase circuit, it is recommended that after a fault occurs and one or two LUHFSER fuses operate, they should all be replaced since the remaining fuses, even if they appear to be intact, may have suffered deterioration of the fuse wire and alter the current vs. time fusing characteristics.
Para la identificación del tipo de fusible según la corriente nominal, se recomienda fijar o ponchar una Shakira de color en el extremo del cable del fusible. El material debe ser polimérico, resina o fibra con propiedades de protección para los rayos UV que mantenga el color de la Shakira con el tiempo
The effects of uses contrary to those indicated by the manufacturer for Colombia shall be the responsibility of the installer or user of the product.
DANGER OF ELECTROCUTION AND ESCAPE.
- LUHFSER fuses cannot protect personnel from electrocution.
- Distribution dropout fuse cutout can expel hot gases and particles at high velocity during interruption.
- When engaging a distribution dropout fuse cutout , clear all personnel from the work area.
- Ejection of the dropout fuse cutout can cause serious injury. Do not align with the pole and fuse holder. Stay clear of the conical space under the fuse holder.
Desea realizar una cotización?
con gusto atenderemos su solicitud o cualquier duda que necesite
